Check It Out

 

What are your opinions with regards to Tools You Need to Install a New Bathtub ?

Setting up a bathtub isn't precisely rocket science, however it does require strong plumbing, woodworking, and in some cases, tiling skills. Changing an old tub with a brand-new one is likewise a moderately hard job. If the old bathtub is easily accessible, the task can move easily; if you have to open up a wall to eliminate the old bathtub and place the brand-new bath tub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will need a helper to vacate the old bathtub as well as set in the brand-new one. See to it you have actually qualified on your own for the work as well as are comfortable trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is far better to think about employing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This short article will certainly help you set up a brand-new bathtub in your washroom if you have already acquired a new tub and also don't need to alter the setup of your previous water pipelines.
Your devices and also material checklist should consist of the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Planning for the Installation

Firstly, the supporting frame provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets unit to prevent strain on the bathtub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last placement.

 

 

Removing Old Touches

If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be rather problematic because of the limited gain access to that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipelines. As soon as the supply pipelines have been eliminated, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing compound.
Prior to carrying on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.

 

 

Mounting the Bathtub

Making use of the two wooden boards under its feet, place the bath tub in the needed position. The wooden boards are valuable in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 small factors.
The next objective is to guarantee that the tub is leveled all round. This can be achieved by examining the spirit level as well as changing the feet on the bath tub until the level reviews degree.
To install taps, fit the bottom of the outermost adaptable faucet port to the ideal supply pipe by making a compression sign up with; then do the very same for the various other faucet.
Activate the supply of water and examine all joints and brand-new pipework for leaks and also tighten them if essential. Fill up the bath tub as well as additionally examine the overflow outlet and also the typical outlet for leaks.
Finally, deal with the bath paneling as defined in the producer's user's manual. Tiling and also sealing around the bathtub must wait till the bath tub has been used at least once as this will certainly resolve it right into its last position.

 

 

Fitting New Touches

If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin making certain that the washers are in place in between the tap and also the sink. Secure the tap in place with the maker given backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former kind must be connected to the tap finishes first, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Bathtub

In the location where the bath meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are marketed in tubes as well as cartridges, as well as can securing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to securing, to allow for the motion experienced when the tub remains in usage. The sealer can fracture fairly early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or waterproof glue and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you enjoyed our part on How to Install a Bathtub Yourself. Thank you so much for taking a few minutes to read our article. Enjoyed reading our post? Please share it. Help somebody else discover it. I recognize the value of reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Quality service? Ring us.